[REŠENO] WV Pasat B5 centralna brava

Forum za autoelektroniku i autodijagnostiku
grki
Expert
Expert
Postovi: 468
Pridružen/a: 31 sij 2012 15:02
Imam problem sa Pasatom B5 upravo sa centralnom bravom na istom ,problem je u tome što kad se pokuša zaključati na daljinski žmigavci blicnu normalno a centralna brava ne reaguje,kada se sve to ručno zaključa na daljinski hoće da se otključa.Znači hoće da otključa ali neće da zaključa.Dali je neko imao ovakav problem ,svaka pomoć dobrodošla.
nerminb
Expert
Expert
Postovi: 266
Pridružen/a: 19 ožu 2013 23:37
Lokacija: Mostar BiH
Kakvu dijagnostiku imas.
Avatar
audiopoint
Expert
Expert
Postovi: 558
Pridružen/a: 31 lis 2013 22:04
Lokacija: skopje
proveri modul ispod 'noge' vozaca
nerminb
Expert
Expert
Postovi: 266
Pridružen/a: 19 ožu 2013 23:37
Lokacija: Mostar BiH
Bez dijagnostike, ce tesko sto uraditi. Mislim da treba samo jednom ponistiti i ponovo dodati daljinske u modul.
grki
Expert
Expert
Postovi: 468
Pridružen/a: 31 sij 2012 15:02
Kaceno je na dijagnostiku radjen je restart ali nece ponovo
nerminb
Expert
Expert
Postovi: 266
Pridružen/a: 19 ožu 2013 23:37
Lokacija: Mostar BiH
Obrisi jednom kljuceve u central conv. i ponovo ih dodaj. Pokusaj ovo

Remote Control Programming

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Using the remote control press the Unlock button once, and the horn
will sound once.

4. Wait 6 seconds and press the unlock button once to activate the coding
procedure. The remote control will now be programmed.

NOTE : When performing programming on additional remotes the procedure
is the same, except you press the unlock button 2, 3 or 4 times for the
different remote.

For example : If programming 2 remotes press the unlock button twice with
a 1 second interval between each press, repeat for 3 and 4 remotes.

5. Switch Ignition OFF.

6. Remove key from ignition and check for operation.

7. The coding procedure can be repeated up to 4 times for additional remotes.

8. The ignition must be switched OFF between programming each remote
control.

Remote Control Erasing

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Press the remote control unlock button 5 times in 1 second intervals.
A short horn will sound.

4. Wait 6 seconds and press the unlock button once to activate memory
erase.

5. Switch ignition OFF, all remotes are now erased.
grki
Expert
Expert
Postovi: 468
Pridružen/a: 31 sij 2012 15:02
Reseno problem je bio u motoru za otvaranj prozora kod vozaca,i kompijuter koji se nalazi ispod tapacira vozaca je bio sav u vodi tako da savetujem ako neko ima problem sa ovim vozilom prvo pogleda dali je kompijuter vlazan ,kompijuter sam osusio a motor zamenio.Da dodam da mi je jos pravio problem sa bravom gepeka kada zakljucam rucno auto otvori sve prozore.
Avatar
audiopoint
Expert
Expert
Postovi: 558
Pridružen/a: 31 lis 2013 22:04
Lokacija: skopje
posle 15 dana poslusao savet :roll:
grki
Expert
Expert
Postovi: 468
Pridružen/a: 31 sij 2012 15:02
Poslusao sam pre savet nego nisam pisao post dok nisam zavrsio auto